visit our website at: www.panduit.com/ncg network connectivity group spec sheet specifications technical information applications sc fiber optic connectors shall be compliant with tia focis-3. sc connectors shall contain a factory terminated pre-polished multimode fiber, requiring no field polishing and no adhesive. the fiber shall terminate in a 2.5mm ferrule and have a typical insertion loss of 0.3db (62.5/125m) or 0.35db (50/125m) per connector. sc o pti -c rimp ? fiber optic connector ? pre-polished crimp ? the sc o pti -c rimp fiber optic connector improves an industry standard design. elimination of end face polishing and adhesive provides for easier, faster installation, especially in remote areas and confined spaces. this reduces installation time over standard field polish sc connectors by 50%. sc fiber optic connectors are widely used in fiber optic backbone and horizontal applications for high-speed data transmissions. *st is a registered trademark of lucent technologies. key features and benefits pre-polished fiber stub eliminates polishing steps, speeding installation vfl verification during provides installer with a visual signal when optimal crimp process continuity is made and the crimp step can be performed mechanical crimp consistently provides higher than industry standard cable cable retention retention; requires no adhesive, speeding installation proven 2.5mm uses standard termination tools and procedures; provides ceramic ferrules strength and reliability robust design protects fibers from mechanical and environmental stress non-optical disconnect network reliability; maintains data transmission under tensile loads (jacketed cable only) focis-3 compliant ensures intermatability with all focis-3 compliant components exceeds tia/eia-568-b.3 network reliability assured as defined by tia fiber compatibility: 62.5/125m and 50/125m multimode versions available fiber cable type: tight-buffered cable only (3.0mm jacketed or 900m) ferrule type: zirconia ceramic with a pre-polished fiber stub insertion loss: 0.3db typical (62.5/125m), 0.35db typical (50/125m) return loss: greater than 20db sc o pti -c rimp multimode connectors 62.5/125m black boot: fscmmbl 62.5/125m red boot: fscmmrd 50/125m black boot: fscmm50bl 50/125m red boot: FSCMM50RD sc adapter modules with phosphor bronze split sleeves duplex: cmdeisc** simplex: cmseisc** sc adapter modules with zirconia ceramic split sleeves duplex: cmdbuscz** simplex: cmsbuscz** multimode patch cords and pigtails duplex sc to sc: f^d3-3m? simplex sc to sc: f^s3-3m? simplex 900m buffered sc pigtail: f^b3-nm? duplex st* to sc: f^d2-3m? duplex fj ? plug to sc: f^d6p-3m? ^available in 62.5/125m (6) and 50/125m (5). ?patch cords are available in 1, 2, 3, 5 and 10 meter lengths, and pigtails are available in 1, 2 and 3 meter lengths. opti-crimp termination tooling termination kit: fjmvkit to upgrade from fjkitg, purchase fjqcvr fiber cleaver tool and fvflkit visual fault locator kit. to upgrade from fjmkit, purchase fvflkit visual fault locator kit. terminate on tight-buffered cable only. always use fvfl visual fault locator during termination. installer tips **substitute for colors: ei = electric ivory bu = blue bl = black iw = off white aw = arctic white
sc o pti -c rimp ? fiber optic connector ? pre-polished crimp 900m boot standards compliant connector performance tia 455 description test procedure and tia/eia-568-b.3 required performance typical performance 1 flex 100 cycles; -180 to 180 degrees; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 2 impact 8 drops from 1.8m; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 4 high temperature 4 days at 60c followed by post-conditioning fotp-6; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 21 durability 500 mate/unmate cycles; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 36 tw i s t 10 cycles; 2.5 cw, 5 ccw, 2.5 cw; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 185 coupling strength 7.4 lbs. at 0 degrees; max. insertion loss 0.75db, min. return loss 20db < 0.1db additional loss 188 low temperature 4 days at 0c; max. insertion loss 0.75db, min. return loss 20db, max. change during test 0.3db < 0.1db additional loss 34 insertion loss max. insertion loss 0.75db 0.3db typical (62.5/125m), 0.35db typical (50/125m) 107 return loss 20db minimum >20db 5 humidity 4 days at 90-95% rh and 40c; max. insertion loss 0.75db, min. return loss 20db, max. change during test 0.4db < 0.1db additional loss 6 cable retention 11.24 lbs. at 0 degrees, 4.4 lbs. at 90 degrees; max. insertion loss 0.75db, min. return loss 20db, max. additional loss 0.5db < 0.1db additional loss note: multimode tests performed at 850 and 1300nm. 3mm boot 2.04 [51.9] 2.32 [59.0] dimensions are in inches (dimensions in brackets are in millimeters) panduit corp. tinley park, illinois 60477-3091 customer service: 800-777-3300 technical support: 866-405-6654 email: ncginfo@panduit.com website: www.panduit.com/ncg panduit canada markham, ontario phone: 800-777-3300 panduit europe ltd. london, uk phone: 44 208-601-7200 panduit japan tokyo, japan phone: (81) (3) 3767-7011 panduit asia pacific pte. ltd. republic of singapore phone: (65) 6379 6700 panduit australia pty. ltd. victoria, australia phone: (61) 3-9794 9020 panduit latin america jalisco, mexico phone: (52) (333) 666-2501 network connectivity group contact your local authorized panduit distributor for pricing. for your local sales office call 800-777-3300 for a copy of panduit product warranties, log on to www.panduit.com/warranty for a full line catalog (sa-nc10cb01a), email us at csteam@panduit.com or call customer service at 800-777-3300. ww-fbsp03 07/2003 ? panduit corp. 2003 all rights reserved printed in u.s.a. worldwide subsidiaries and sales offices
|
